Spring is right here, however at my home, winter has left its mark on nearly the whole lot. Out again, the outdated patio deck has been warped by rain, solar, freezes and thaws, its boards now not laying flat however rattling underfoot. Indoors, issues are worse. The floorboards have been groaning since December, desiccated by furnace-heated air till they shrank, got here free and commenced rubbing in opposition to each other.
If both of those issues sounds acquainted, this month’s D.I.Y. column is for you. We’ll cowl just a few easy methods to take care of loud, free floorboards. We’ll additionally be taught a bit about that humble hero of house repairs — the nail — and the way to decide on the suitable one for no matter job you’re engaged on.
In case you have creaky flooring, you and your neighbors will take pleasure in some welcome quiet. In case you have a deck, you’ll find yourself with a extra snug place to hang around because the climate warms up.
Fortunately, the instruments and supplies for these tasks are low cost. The work goes rapidly, and the outcomes will probably be virtually invisible (apart from decking fasteners, which aren’t meant to be invisible anyway). Maybe better of all, the venture will make you extra assured along with your hammering, a ability that transfers to any variety of home-improvement duties.
If there’s a bigger D.I.Y. lesson right here, it’s one I’ve taken from my very own previous fiascos: Don’t overcommit in the beginning. There are often a number of methods to strategy a venture, however some are all-or-nothing — which means there’s no altering course when you’ve begun. As an alternative, I like to start out with a step that’s simple to reverse, or no less than to hide, and that doesn’t render alternate approaches troublesome or unimaginable.
Nailing a free floorboard into the joist under ought to get rid of the rattle or squeak. But when it doesn’t work, it’s simple to undo or disguise, and nonetheless leaves the opposite, extra concerned strategies on the desk. (We’ll contact on a few of them later.) Fairly often it does work, although, making the straightforward nail not simply the low-commitment methodology, however the suitable one.
Let’s collect the instruments.
Floorboards
Job one is to find the joists — the under-floor beams that the floorboards are fixed to. If the creaking noise is coming from the top of a board, you’re in luck: The ends of every floorboard (the place the nails will go) invariably relaxation on a joist. If the creak is coming from the center of a board, hint a line (think about using a ruler or different straightedge) from the top of a close-by board to the one which’s creaking, and also you’ll discover the place the joist passes beneath.
When you’ve obtained a number of creaky boards, use some painter’s tape or sticky notes to mark them out . They usually cluster collectively, and generally one or two new nails in a few the boards will silence the whole thing.
The important thing function of flooring nails is their slim head, barely wider than the shank of the nail itself. They’re made that manner in an effort to drive the nail head under the floor of the board after which conceal the outlet. It’s a attribute of the broad class of trim nails, and for any venture the place you want a clear end — when you’re making an image body, for instance — trim nails are what you need.
Decking
With outside decking, the issue is often boards which have fully indifferent from the deck framing. The boards are held on with lengthy screws or nails, and after years of publicity to the weather they finally rust away or just lose their grip. Unfastened deck boards often don’t squeak, however rattle while you step on them or give them a rap along with your fist — the best methods to find them.
Repairing a free deck board is easy. When you’ve recognized one, use the unique fasteners (or the holes the place they was once) to indicate you the place to position a few new nails. Drive them in half an inch or so from the outdated fasteners, in order that they’ve contemporary wooden to chunk into.
A rotten — not merely free — board is a distinct matter. It’s going to exhibit telltale indicators: spongy or crumbly areas, lengthwise splits that flex open while you step on them, deep cracks that lower throughout the grain of the wooden. For security’s sake, don’t attempt to restore a rotten board. Exchange it with a brand new one. When you discover rotten structural beams below the decking, it’s time to get the entire thing professionally rehabbed.
The heads of decking nails, and of development nails normally, are broad, flat and skinny. The broad head resists any effort by the board to tug itself out (if it later warps, for instance), and its skinny, flat form lets the pinnacle lie flush with the floor.
You’ll discover development nails in a variety of sizes at your ironmongery shop; the thinner your boards, the thinner the nail you need to select, to attenuate the prospect of splitting the wooden. For outside tasks, use nails designated for outside work. Most will probably be zinc galvanized to guard in opposition to corrosion. Stainless-steel and bronze nails are additionally accessible, however rather more costly.
Options and Caveats
The methods above don’t work in each state of affairs. Wood flooring usually have a subfloor — plywood or, in older properties, simply low cost lumber — between the floorboards and the joists Generally it’s the subfloor that’s squeaking, so nailing down the floorboards doesn’t all the time repair the issue.
If skinny trim nails fail to cease your squeaks, you may attempt utilizing beefier hardened ground nails with a spiral-shank or ring-shank — just like those we talked about earlier for decks. They clench boards collectively extra tightly. You’ll want a drill, nevertheless. Utilizing a bit barely narrower than the shank of the nail, pre-drill a gap for the nail, in order that it received’t cut up the floorboard while you hammer it in.
There are additionally particular screws which are designed to tug the flooring, subfloor and joists collectively tightly, after which snap off under the ground’s floor. (Squeeeek No Extra might be the best-known model.) If nailing doesn’t work, they’re value a shot. Once more, you’ll want a drill.
In case you have free parquet flooring, they need to simply be glued down. Parquet boards are primarily picket tiles. Pull up the free boards — a skinny screwdriver or paint scraper might help pry them out — then apply a layer of wooden glue or a skinny bead of development adhesive, set the boards again in place, and maintain them down with one thing heavy till the adhesive units.
