Should you’re in search of a spot to retailer your firewood that is also tremendous cool to take a look at, take a look at this firewood holder DIY. Earlier than, I might simply have my totally different sizes piled up in containers across the fireside, which was actually unattractive. So on a whim I threw these collectively. The three compartments permit me to separate small, from medium, to massive items of wooden. Seize a set of plans and let me present you ways I construct them.
Let’s Construct A Firewood Holder
DIY Firewood Holder Plans
$9.99
I’ve created a set of plans to make constructing this firewood holder fast and straightforward!
Supplies I Used on this Construct:
Step 1: Choosing Materials and Slicing to Measurement
I did design and construct these on a whim so when choosing materials, I simply seemed round my store to see what I had already that may match the sizes. I discovered this stack of three/4” reduce off from some cabinets I tore a component that I’ll make the physique from. Then for the again, I’ve some 1/2” plywood from who is aware of what.
I began off by ripping the sheets all the way down to width wanted. If you would like actual dimensions, I’ve a set of plans out there over on my web site. I tilted the blade over to then reduce within the angles wanted to created the pointed miters. Since there are a whole lot of repeated elements, I arrange a cease block in order that I might make all of them the identical. If you do that, you need to make certain to set the cease block again far sufficient so the board received’t be touching it when it contacts the blade. As that is what may cause chill.
To avoid wasting from switching the blade forwards and backwards, after chopping one facet with the wanted angle, I might flip the board and reduce the opposite facet because it nonetheless had a 90 on one finish. This may go away the remaining board with angles on each finish, that I can chop up for the mitered elements. I personally prefer to at all times do a take a look at first and a dry match to ensure issues are going to work as I’ve them deliberate. That appears good although.
Step 2: Banding the Edges of the Firewood Holder
Now I simply wanted 12 of them whole so I locked within the new distance for the fence for this half and chopped up the remaining bit into items.
This challenge solely consist of 4 totally different elements. What I’ll name the facet, the tops that are barely longer than anything, the horizontal cabinets, then the mitered factors. Remember the fact that it might be easy so as to add extra to subtract the variety of cubbies, relying in your areas wants.
Alrighty, now I’ll edge band the perimeters that can be going through the entrance. Truly, on second thought, I like the thought of portray them as an alternative. Observe: that if you happen to edge band you’ll want to do this earlier than becoming a member of the elements collectively, however if you wish to paint, then you possibly can go straight into assembling.
Step 3: Assembling the Firewood Holder Cubicles
For assembling, I began off on high of my workbench and what I did is apply some wooden glue, I’m utilizing DAPs weldwood right here, to each joint, then pin nailed issues collectively utilizing my 23 gauge nailer. It is a fairly weak joint till the wooden glue has time to arrange, so I used to be being cautious as I used to be transferring it round to connect the following leg. If I didn’t have a 23 gauge, I might have used a 18 gauge as an alternative.
After getting a couple of hooked up, I believed it might make issues simpler to do it on the bottom so I might see all the things clearly as I used to be attaching legs. So I moved it all the way down to the ground and continued. I might juke and jive to create the factors of the cubbies, then connect the horizontal that can create the separation between.
I paused once I bought to the very high as a result of the way in which I’ve it designed, the highest edge will really be seen. With that, I edge banded each of those elements earlier than including them on. This is so simple as heating up an iron and warming up the glue on the again of the banding till it sticks to the plywood edge. This can be barely totally different than the ply, but it surely doesn’t hassle me.
Step 4: Portray the Firewood Holder Cubbies
I left that the place it sat to present that glue time to arrange and dry. Whereas it was, I grabbed items that can make up the again from my 1/2” plywood scraps. I additionally grabbed the items that can make up the edges. I would like each of those to be painted the identical colour as my wall which implies I want to present them a couple of coats earlier than attaching the cubbies.
Since I’ve the paint out, I additionally needed to color that entrance fringe of the cubbies. I first give them each a very good sanding to get them easy. Now when working with plywood, there are sometimes voids on each single edge. So as to get a easy trying paint floor, I apply some wooden filler on a putty knife. I’m utilizing DAP Premium wooden filler. These things not solely dries quick however is simple to sand and is nice to paint match if you’re staining one thing.
After letting it dry for about 30 minutes, I got here again with a sanding sponge to knock it down flat in order that I might roll on the paint onto the items of the firewood holder.
With ending out of the way in which, let me simply push this button right here to lift my ending shelf up and find the {hardware} I’ll want to connect the cubbies to the again.
Step 5: Shaping the Again to Match the Firewood Holder Cubbies
I began with a again barely bigger than what I wanted, then plopped the cubbies down onto it and lined it up in order that the underside cubby was flush to the top of the plywood. I used my pin nailer to only tack issues in place to start out. The tip is simple appropriately flush, however to ensure the remaining weren’t crocked, I pulled a tape to get the spacing good earlier than tacking the remaining. With it not in a position to fall off now, I tilted the complete unit on it’s face in order that I might have entry to the underside to throw in screws. Right here, I made certain to pre drill to stop splitting.
Step 6: Securing the Firewood Holder Cubbies to the Again
The highest location is simple to find as a result of you’ve got a visible on the place the shelf is positioned. Nevertheless, the second is difficult as a result of it’s in the course of nowhere. What I do is seize a velocity sq., this Crescent one has a further 6” flip out rule in order that I can place it within the middle of the shelf, go all the way down to the dimension wanted, and pre drill. Should you don’t have this velocity sq. or one other lengthy one, then a stage would additionally do the trick.
For the angled portion of the cabinets, the velocity sq. wouldn’t work, so I grabbed a scrap and reduce in an angle on the tip. This manner I might relaxation it on the shelf and permit me to mark the peak. Ensuring to maintain it in the identical location, I moved the scrap to the face closest to me to now drop it down again to the road I made which supplies me the placement of the angled shelf to pre drill and connect a screw.
With the again on, this factor now feels actually safe and powerful. I flipped it up to have a look. I really assume it seems to be fairly good with a sq. again on it and was contemplating leaving it as is however then I made a decision to stay to my unique plan and make the again flush to the geometric form. I wasn’t in a position to find my palm router, which is definitely the best instrument to trim the again off, so as an alternative I put a flush trim bit in my router desk and trim it off that manner. The important thing right here is to maintain the unit good and flush on the desk as you progress it alongside.
I laid the unit over and hooked up the facet. This may assist help the horizontal cabinets that can really be supporting the load of the firewood.
Step 7 : Putting in the Firewood Holder and Slicing Firewood
Last item to do was set up them. Now I personally needed mine up off the bottom so I wouldn’t block an outlet I’ve over on the proper hand facet. Then I additionally like to make use of this space for storing my video games and puzzles. With that, I propped the items up, discovered the studs, then drove a couple of screws into the again of the unit to connect them.
Okay lets load it down and see how a lot it could maintain. Now that, is significantly better than earlier than. As a substitute of ugly containers and totes, I now have a pleasant firewood holder with devoted house for the wooden. This may permit me room to retailer and separate all totally different sizes of firewood throughout winter. Then I personally just like the look of wooden sufficient to maintain it full yr spherical, however I might additionally retailer different kinds of nicknacks throughout spring and summer time ought to I need to.
What do y’all take into consideration them? Bear in mind how simple it’s to make bigger or smaller. I even assume they’d look good horizontal, relying in your house. I’ve a set of plans for this challenge in addition to many different over on my web site. In reality, if you would like firewood storage concepts, I’ve a couple of of them.
I’ll see you subsequent time.
