Let’s Construct a Laundry Drawer!
DIY Laundry Drawer Plans
$9.99
Supplies I Used to Construct the Laundry Drawer
Step 1: Chopping Items for the Drawer
It takes 7 components to make the physique. So not many. If you need a set laundry drawer plans with dimensions then I’ve that out there, it additionally comes with a CNC minimize file you probably have a CNC. I personally painted my cupboards so I simply used no matter 3/4” sheet materials I had scraps of which is MDF on this case.
I begin by laying the facet items on their again and attaching what would be the backside. When becoming a member of issues collectively, it is going to be the identical course of on all the pieces, I used DAPs weldwood wooden glue then predrill and run in a screw
Step 2: Getting ready the Toe Kick Plate and Attaching Laundry Drawer Sides
This ledge right here shall be the place the toe kick plate goes in, which is that this board right here. I’m utilizing it as a spacer to ensure the underside is connected sq.. After utilizing it to align the board from the within, I additionally used it as a spacer to information me on the place to pre drill and run in a screw. Double checking that it labored; it did, so I proceed attaching. I used this trick once more once I wanted to run within the middle gap. So long as the board is flush to the entrance, it should point out the place the three/4 materials begins for the pre drill gap.
After attaching the primary facet, I connected the second facet the identical method. Nonetheless because the toe kick now can’t match inside to verify for sq., I simply used a tape. I measured the highest, then made certain the underside matched earlier than driving in my screws to connect it.
Step 3: Attaching the Toe Kick Plate
Subsequent is to connect the toe kick, which ought to line up completely flush to each of the facet items and the entrance and the again. Identical with the again board that may make up the again of the platform as soon as this cupboard is stood up proper. Excellent, that’s the backside performed so now lets flip this round, however nonetheless go away it on it’s again, and begin engaged on the highest boards. This board right here will be a part of the edges out on the again edge whereas additionally giving me a spot to screw it into the wall afterward when putting in it within the house.
When becoming a member of one thing flush like this, I like to maneuver my work piece to the sting of my workbench if potential. This fashion my drill has room to go in straight as a substitute of at an angle the place I may blow out a screw.
Step 4: Attaching the Final Board
The final piece to connect here’s a related board because the final however this one joins the entrance fringe of the edges. Since I can’t use my workbench to relaxation it in opposition to, what I love to do is use a clamp to behave as a 3rd hand. These squeeze clamps are nice to carry them within the basic space whereas I get one facet at a time completely positioned and connected. This board will give me one thing to screw up right into a countertop later when it will get put in.
Step 5: Including the Again to the Laundry Drawer
Okay, with that connected, now let me spin this round, tilt it up, and similar to that we’ve got a cupboard. Oh, I forgot the again. Maintain on, that’s a fast add. Lets simply lay this factor again down, however this time laying it on it’s face. I made the again from 1/4” mdf because it doesn’t should be tremendous thick. 1/4” materials will do a fantastic job at holding it sq. and conserving it from racking.
You’ll see that my again is in two items. That’s as a result of I’m utilizing scraps and don’t care concerning the again, which shall be on the within and by no means seen, has a appear. If it does hassle you although, you’ll be able to at all times make it from one stable piece
Alrighty, and now that’s a accomplished physique. So for now, lets simply slide this on over to make room for me to usher in the components to construct out the within drawer that may maintain the baskets.
Step 6: Securing the Match and Attaching the Sides
All of those components are additionally included on the plans and cutlist however I seize for what would be the backside first. I personally at all times like to ensure it matches inside the physique earlier than attaching issues simply because I’ve been identified to seize the unsuitable half earlier than however as soon as I made certain it match, I connected the 2 sides which appear like wings. These have dados minimize into them for the underside to slide proper into.
This backside shall be locked in as soon as the back and front are connected, however I went forward and threw in a number of screws. I went to the again and connected the specialty designed again. These slots and these predrilled by means of holes are wanted for the below mount drawer slides that I’ll be utilizing.
For those who use my precise dimensions then you can’t solely use the precise hampers that match on this laundry drawer but additionally the precise drawer slides. Nonetheless, know that if you wish to change dimensions you then’ll most likely need to get totally different drawer slides and alter the design of this again half. An alternative choice is to vary the size to what you need, however then use facet mount drawer slides and never fear concerning the below mount ones. A number of choices.
Step 7: Finishing the Entrance Meeting
Going to the entrance of this meeting, I connect the big entrance panel. This may appear large and boring proper now however you’ll see why the size is required. For now, let me go forward and put it contained in the physique to ensure all of it seems to be good……annnnd it does. It’s so simple as that, now all the pieces right here on out are ending particulars.
Step 8: Making the Laundry Drawer Slide!
I may connect the below mount drawer slides to the underside facet of the cupboard. Appears to be like like this right here. Then go to the within of the cupboard and connect the rails with screws. To attach the 2, I may carry the within portion over to the physique, set it on the rails, then push it in till the 2 elements clicked collectively. It’s so satisfying. Then since I’m making mine appear like two doorways and a high drawer, I crawled inside and connected these items to the skin by screwing them in on the within whereas Jacob held them to the correcting spacing.
Conclusion: The Completed Product
It’s kinda laborious to get angle of this cupboard as a result of the house is de facto tight however with out the counter high in place you’ll be able to see the way it works. Two hampers match completely on the drawer so to pull it out and toss in your garments, then conceal them away once more by pushing it in. Gentle closed after all.
Even with the countertop on, I’ve loads of room to take the baskets out and in or just toss in garments then reshut it. I like the way it seems to be like three elements. The place because the unit on the left actually is a high drawer and two doorways on the underside.
I’ve a 4 half collection of movies the place I cowl find out how to correctly paint MDF, find out how to construct customized cupboards, find out how to improve retailer purchased cupboards, and likewise find out how to construct a countertop from scrap 2x4s! So principally if you wish to see how I constructed out the complete room you’re , then verify the hyperlinks within the description. For those who can think about it, you’ll be able to construct it and I hope I’m an inspiration or information that will help you get began. I’ll see you on my subsequent venture.
