Sanding metallic is an important a part of the preparation course of when restoring radiators, getting ready backyard furnishings for portray, and freshening up a entrance gate. It is also an effective way to take away rust by cleansing affected surfaces.
Nevertheless, when sanding metallic, it is important to pick the correct instruments, select the suitable sandpaper grits, and make use of the right methods to realize the sleek, clear end you want. Get it fallacious and you would be doubling your workload or be left with a less-than-satisfactory floor. Right here, you’ll discover all you should know to make sure that doesn’t occur.

Paul began his profession with a small, unbiased stainless-steel stockholder over 35 years in the past. He then labored for Delta Metals plc earlier than recognizing a chance to develop and construct metals4U as a powerhouse for the net provide of metals. He took the possibility and has by no means seemed again.
Generally sanded metals
Sanding metallic is a standard course of for a wide range of causes, as Paul McFadyen, metallic knowledgeable and chairman at metals4U, explains: “Whether or not it’s for a DIY mission, restoration, or prep for portray, there are numerous metallic gadgets that generally want sanding.”
He continues, “Metal and wrought iron are usually used for gates, railings, backyard furnishings, and radiators, and are normally sanded to take away any rust and peeling paint earlier than repainting.”
McFadyen mentions different well-liked choices “Equally, aluminium gadgets like automobile components and bodywork, cookware, and sure instruments and equipment, will profit from sanding to revive shine and enhance the adhesion of any finishes. Sanding aluminium can clean over any scratches and put together this stuff for paint and polish.”

Leigh Begin joined The Metallic Retailer in 2015 and was appointed Managing Director in 2023. With practically a decade of expertise within the metallic provide trade, Leigh has performed a key function in driving the corporate’s progress and increasing its service providing.
Protecting gear you will want
When working with metallic, it is important that you’ve got the correct security gear to guard your self. Leigh Begin, managing director at The Metallic Retailer, says, “Security ought to by no means be missed.” He recommends that you simply at all times put on the next:
- Protecting gloves to stop cuts from sharp metallic edges.
- Security goggles to defend in opposition to mud and particles.
- A mud masks or respirator to keep away from inhaling fantastic metallic mud.
- Ear safety if utilizing energy instruments.
Instruments you’ll must sand metallic
What instruments you’ll must sand metallic will rely on what kind of sanding job you might be tackling. Right here Begin lists the frequent choices:
- Orbital sander for bigger jobs.
- Wire brush or flap wheel attachments for eradicating rust.
- Sanding blocks for hand sanding.
- Element sanders or sanding sponges for hard-to-reach areas.
Finest methods to sand metallic
Earlier than any sanding is carried out, McFadyen advises that it wants cleansing first: “Step one is to at all times clear the metallic floor to take away any grime or grease that might intrude with the sanding course of. Ensure that the metallic is absolutely dry earlier than sanding.”
McFadyen gives one important tip to comply with: “Begin with a coarser grit and transfer to a finer one as you progress. A rough grit will assist to take away rust and paint earlier than additional sanding, whereas a fantastic grit will give a smoother end.” As soon as the metallic is dry and you should utilize one of many following strategies.
Utilizing an influence sander
Utilizing an influence sander may help pace up the sanding course of, however it have to be used appropriately. McFadyen says, “Ensure that to maintain the instrument shifting to keep away from creating deep scratches and warmth spots.”
He factors out, “A typical mistake folks make when sanding is urgent too onerous, which may create uneven surfaces and scratches.” He provides, “Extreme power can injury the metallic, so follow a average strain. If you end up needing to press more durable for an efficient job, you must swap to a coarser grit.”
An influence sander (like a random orbital sander) is the popular alternative for bigger flat areas. Nevertheless, for extra detailed/intricate areas and edges, switching handy sanding is your best option.
Sanding by hand
For normal hand sanding, Begin says, “Hand sanding entails utilizing a sheet of sandpaper (usually wrapped round a sanding block) and dealing in clean, even strokes throughout the floor. The secret’s persistence and consistency.” He provides, “Keep away from urgent too onerous, which may go away gouges or an uneven end.”
For extra intricate areas the place a sanding block gained’t work, you should utilize the sandpaper straight in your hand. Alternatively, you should utilize a sanding sponge (like these Sanding Sponges from Amazon). These will match the form of the metallic being sanded.
Sanding errors to keep away from
It is easy to make errors when sanding. Right here Begin gives 4 suggestions to assist make sure the sanding course of goes easily.
- Utilizing sandpaper that’s too coarse, which may scratch the metallic past restore.
- Skipping grits – shifting from very coarse straight to fantastic leaves seen marks.
- Making use of uneven strain, which causes dips within the floor.
- Forgetting to scrub the metallic earlier than and after sanding, main to clutter being trapped underneath paint or coatings.
Finest sandpaper for sanding metallic
Begin recommends the next sandpapers for sanding metallic, “Aluminium oxide sandpaper is the go-to for many metalwork because of its sturdiness. For stainless-steel, silicon carbide papers are higher as they minimize cleaner and sooner.” Each of those could be simply discovered on-line or at your native ironmongery store.
McFadyen explains what grits to make use of, “For heavy rust and paint elimination, you’ll probably wish to select a rough 40-80 grit sandpaper. For smoothing tough surfaces, progress to 120-180 grit sandpaper. Lastly, 220-240 grit sandpaper will give your metallic a cultured end.”
He provides, “Metal is usually stronger than aluminium and may deal with coarser grits, whereas moist sanding with a medium grit is more practical for aluminium to stop warping. Copper and brass are a lot softer, so that you’ll want to decide on a finer grit and use mild strain to stop scratching.”
FAQs
After sanding metallic, it is beneficial to scrub the metallic earlier than shifting on to the subsequent stage. Begin says, “As soon as sanding is full, wipe the floor down with a clear material and a solvent similar to acetone or white spirit.” He provides, “This removes fantastic mud and grease, guaranteeing the floor is totally prepared for paint, primer or sealant.”
Water is typically recommended for use when sanding metallic however Begin suggests you don’t. “Keep away from utilizing water when sanding most metals. Moisture encourages flash rusting, which may undo all of your onerous work. As a substitute, preserve the realm dry and clear as you go.”
He provides, “Moist sanding is typically utilized in specialist purposes similar to automobile bodywork, however for many dwelling and backyard metallic tasks, holding the method dry is safer and more practical.”
If you happen to’re trying to replace your radiators, you’ll must sand and prep earlier than you begin. To get the end you need, try our guides Learn how to paint a radiator and Learn how to paint behind a radiator. Alternatively, when you don’t wish to paint your radiators, attempt our radiator cowl concepts for inspiration.