I’m making regular progress on my walk-in closet. I lastly needed to take a time without work on Friday, although. I had been working for 2 weeks straight with no break on the closet, and my exhaustion hit a degree on Friday that I made a decision I wanted to take sooner or later to relaxation earlier than I injure myself. So on Saturday, I used to be in a position to get to the enjoyable stuff — including trim to the boring plywood containers and cabinets. I used to be so excited to lastly get thus far as a result of it’s the trim and molding that take advantage of distinction.
This is just one half of what is going to be a really lengthy collection of posts on my largest constructed but — my walk-in closet and laundry mixture. When you missed the earlier submit, yow will discover that right here: Closet Progress – The Primary Construct Is Completed!
After ending the fundamental construct on this closet, that is what the cupboards seemed like…
And since it’s the facet that requires probably the most trim, I made a decision to begin to begin trimming out the appropriate facet of the room first.
Right here’s what that facet of the room appears like now with the entire trim hooked up. I nonetheless have to put in the molding — the baseboards alongside the underside and the crown molding alongside the highest.
To trim out this facet, I began with the longest horizontal items. On the underside, I used 1″x4″ pre-primed lumber.
And alongside the highest, I used 1″x6″ pre-primed lumber.
I made a mistake proper from the start as a result of I mitered the surface corners of the highest 1×6 boards. These ought to have been reduce straight. However I used to be working alone, and wrestling that 140-inch into place and nailing it into place, there was no manner I used to be going to take it down to chop it straight. So I made a decision to disregard it at this level and deal with it in a later step.
With the 2 prime and backside horizontal items in place, I then hooked up the lengthy vertical items. I nailed the entire trim in place utilizing 16-gauge 2-inch nails by the face of the trim items and into the perimeters of the plywood. I used 1″x2″ items for the 2 exterior vertical items, after which 1″x4″ items for the 2 on both facet of the middle part. However earlier than attaching these, I used my desk noticed to tear them down to three.25″ broad in order that they simply lined the perimeters of the plywood containers in addition to the ends of the shelf helps.
And eventually, I used 1″x2″ lumber to cowl the perimeters of the cabinets.
Right here’s a take a look at the progress from the opposite course…
I did the entire wooden filling as I went, and in case you’ve been round for some time, you already know that I exploit wooden filler very liberally. I do that for 2 causes. First, wooden filler shrinks because it dries. So in case you attempt to put it on completely clean, it should shrink into the joints and screw holes/nail holes because it dried, requiring a second coat. I keep away from having to do a second coat by type of mounding it up on the joints and screw holes/nail holes. But additionally, I exploit my rotary sander to sand all of this clean as soon as it’s dry, so my sander makes very fast work of eradicating the entire extra and making these joints and nail holes/screw holes very clean.
So I ended my weekend by ensuring that each one of these joints, nail holes, and screw holes had been crammed with wooden filler.
I solely use wooden filler to cowl nail holes, screw holes, and joints the place two items meet on the identical aircraft. In different phrases, if it may be sanded clean with a rotary sander, I exploit wooden filler. If two items meet at an angle, for instance, the place the cabinets meet the cupboard containers, these areas get crammed with caulk. I didn’t get to that step but, and these cupboards would require a number of caulking earlier than I can prime and paint.
So that you’ll discover that I solely used wooden filler on the face of the trim the place they meet on the identical aircraft. However I didn’t use wooden filler the place the 2 trim items meet on prime of the shelf and kind a 90-degree nook. These areas will likely be caulked.
However I did use wooden filler the place the trim and the plywood shelf meet on prime of the cabinets as a result of that may be simply sanded with my rotary sander and go away a wonderfully clean transition between the 2 items.
I’ll wait till the opposite facet is trimmed out and the wooden filler has had time to dry on that facet earlier than I begin sanding in order that I can do it . So that is the place I left issues final evening. I additionally didn’t do any wooden filling on the washer cupboard as a result of I nonetheless have to take away that prime trim piece and rip it down only a bit for my washer to suit inside the cupboard.
To treatment my mistake on the highest trim items the place I had mitered the corners as a substitute of slicing them straight, I used my Dremel Multi-Max to chop off the surplus from these boards that caught out previous the sting of the cupboard. The reduce was fairly tough at first, so then I used my rotary sander with 80-grit sanding discs to sand it clean. After which I piled on the wooden filler to fill in between the items. Once I connect the crown molding, that may wrap across the sides of the cupboards by the door and by the home equipment and can proceed across the room.
I repeated that course of on the opposite finish the place I had mistakenly reduce the piece at a 45-degree angle.
Repairing that mistake this fashion was an entire lot simpler than eradicating all the lengthy piece that had been nailed in place with 16-gauge 2-inch nails, eradicating all of these nails, dragging that 140-inch piece again by the home and into the carport to chop off that mitered nook, after which wrestling with that lengthy piece to get it nailed again into place.
In order that’s the weekend progress! It’s actually beginning to take form now.
The underside molding (i.e., the baseboards) will wrap across the base of the tall cupboards in addition to the bottom of the washer cupboard to tie these sections collectively and end off every little thing alongside the ground.
I’ll even be including baseboards contained in the washer and dryer cupboard to complete off the underside of the partitions.
And also you’ll discover that I didn’t add trim to this piece within the middle part. That is going to be my glass-top earring and ring drawer, so this plywood will likely be eliminated. I’m nonetheless making an attempt to find out precisely how I would like this storage designed.
There are two ways in which I can do it. The primary and most evident manner is to construct a daily drawer that pulls out in order that I can entry my earrings and rings. The second possibility can be to construct a storage compartment that doesn’t pull out like a drawer, however as a substitute, the earrings and rings are accessed by placing the glass prime on hinges that raises as much as entry these objects. I type of like each concepts, so I haven’t settled on one simply but.
In fact, the advantage of making it a drawer is that I can set issues on prime of the glass countertop, and with it being a drawer that pulls out, these objects on prime gained’t be disturbed. If I make the glass prime on hinges that raises up for accessing the earrings and rings, I gained’t be capable of set something on prime of that cup space. It must stay free and away from any objects that may block entry. However I nonetheless like the thought. So I’m going to carry off on doing something with that center part till I’ve the small print labored out. I’m nearly 100% certain that I’ll find yourself with one other shelf in that part as soon as I determine precisely how I wish to retailer my necklaces there.
Anyway, it was type of a slower weekend with me taking off on Friday, however at the least there was some progress! And I’m lastly to the enjoyable stuff!
The A2D Day by day:
Addicted 2 Adorning is the place I share my DIY and adorning journey as I transform and embellish the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do nearly all of the work on the home on my own. You’ll be able to be taught extra about me right here.
